Aviom ASI Manual do Utilizador

P/N 9310 1016 0001F rev. 2.00© 2009 Aviom, Inc.User Guide

2Ab o u t Yo u r Pr o 64 Pr o d u c tCat-5eAll Cat‑5e connections between A‑Net devices should use Unshielded Twisted Pair (UTP) cable. The

10Ab o u t A-Ne tAbout A-Net Aviom’s A‑Net® is the only networking technology conceived, designed, and optimized for managing and distributing audio

11Ab o u t A-Ne tused, audio transmission is kept fast and clean, eliminating the audio artifacts and signal degradation inherent to sample rat

12Ab o u t A-Ne tIn Auto Mode, there are no connection rules; connect a Cat‑5e cable to either the A or B port and the network does the rest. Auto

4Fi r m w A r e No t i c eFirmware NoticeAll Pro64 devices in a network should be updated to use the most recent rmware version to ensure trouble-fr

2mA i NtA i NiN g Yo u r Pr o 64 Pr o d u c tAC PowerAlways plug the unit into a properly grounded (earthed) outlet. Always use the AC line cord that

3mA i NtA i NiN g Yo u r Pr o 64 Pr o d u c tVentilationAlways allow adequate ventilation for devices mounted in equipment racks. Avoid placi

9Fr o N t PA N e l co m P o N e N t sFront Panel Components1. Auto Mode LED Manual Mode LED2. Manual Mode Port selection button 3. 4. Port A, Port

10re A r PA N e l co m P o N e N t s1. Power On/Off Switch2. IEC Power Inlet3. Fuse HolderPro16 4. A‑Net ports, EtherCon connectors Pro64 5. A‑

11Fr o N t PA N e l Fe A t u r e sFront Panel Features This section describes the features and functions of all front‑panel components of t

i iTrademarks Aviom, A‑Net, the A‑Net icon, Pro16, Pro64, and Virtual Data Cable are trademarks of Aviom, Inc. All other trademarks are the

12Fr o N t PA N e l Fe A t u r e sIn the example below, the network is operating in Manual Mode, and data from Pro64 Port B will be sent to the Pro1

13Fr o N t PA N e l Fe A t u r e sIn an all‑analog network, the sample rate can be set at the Control Master to the following:44.1kHz•48• kHz88.2•

14Fr o N t PA N e l Fe A t u r e sAt 96kHz, only 32 channels are output to the rear‑panel Pro16 A‑Net outputs. Channels 33‑64 will have no data avai

15Fr o N t PA N e l Fe A t u r e sThe blue A-Net LED indicates that the ASI is connected to an active Pro64 network. Once a module is enumerated an

16re A r PA N e l Fe A t u r e sRear Panel Features All ASI rear‑panel features and functions are described in this section. AC Power Pro64 modules

17re A r PA N e l Fe A t u r e sIn Auto Mode, both Pro64 A‑Net ports are identical. Cables from any Pro64 device can be plugged into either port. Mu

18Asi co N N e c t i o N sASI Connections Building a Pro64 network involves connecting input and output modules, setting A‑Net Slot ranges, a

19Asi co N N e c t i o N sPro64 Parallel ConnectionsThe ASI can be connected to any available port on an MH10 Merger Hub that is part of the Pro64 net

20Asi co N N e c t i o N sCompatible Pro16 Series devices include:• A‑16II Personal Mixer • A‑16R rack‑mount Personal Mixer • AN‑16/o Output Module

21Asi co N N e c t i o N sPersonalMixerSystem BridgePro16 Output ModuleA B C DSystem BridgeA B C DPro16 A-Net Distri

i iiREAD THIS FIRSTImportant Safety InstructionsRead these instructions. 1. Keep these instructions2. Heed all warnings.3. Follow all instructions.4.

22Asi co N N e c t i o N sUsing a System Bridge The Pro16 System Bridge is used to combine up to four Pro16 data streams for transmission over a singl

23Asi co N N e c t i o N sA‑Net In on the next module. To create multiple splits, an A‑Net Distributor can be connected to any port on the System Brid

24sP e c i F i c A t i o N sSpecificationsA-Net I/O - Pro64 2 EtherCon RJ45 connectorsNetwork Sample Rates, Pro6444.1/48kHz; 88.2/96kHz; 176.4/192kHz

25sP e c i F i c A t i o N sDimensions

26sP e c i F i c A t i o N sPro64 A-Net64 [email protected]/48kHzChannels 1-16Channels 17-32Channels 33-48Channels 49-64Pro16 A-Net Pro64 Control Logic1-1

27sP e c i F i c A t i o N sPro64 A-Net64 [email protected]/48kHzChannels 1-16Channels 17-32Channels 33-48Channels 49-64Pro16 A-Net Pro64 Control Logic1-1

28iN d e xIndexAA‑16II, A‑16RPersonal Mixers 5A‑16II Personal Mixer 2, 20A‑16R Personal Mixer 2, 20About A‑Net 3A, B PortsPro64 11AC fusechanging

29iN d e xFber 3Firmware Update 2Front Panel Components 9Fuse 24AC 16Fuse Holder 10GGPIOGeneral Purpose I/O 4HHubMH10 Merger Hub 17IIEC conne

30iN d e xRRear Panel Components 10RJ45 1, 2, 24RoHS iiRS‑232 4null modem cable 2RS‑422 4Ssample rate 20Sample Rate 2, 3minimum/maximum 3, 13

Warranty RegistrationPlease take a moment to fill in this warranty registration form. Return it to Aviom via mail or fax. All information will be kept

i vTO REDUCE THE DANGER OF ELECTRICAL SHOCK DO NOT REMOVE COVERS.NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONL

1157 Phoenixville Pike, Suite 201 • West Chester, PA 19380 Voice: +1 610.738.9005 • Fax: +1 610.738.9950 • www.Aviom.com

vAviom, Inc. Limited Warranty Aviom, Inc. warrants this product against defects in materials and workmanship for a period of one year from the date of

v iWarranty InformationPlease record the following information for future reference:Your Authorized Aviom Dealer:Name: Address: Phone: Serial Num

v i i Table of ContentsWelcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

v i ii Connecting Pro16 Output Modules . . . . . . . . . . . . . 21Using a System Bridge . . . . . . . .

1Ab o u t Yo u r Pr o 64 Pr o d u c tWelcomeThank you for purchasing the ASI A-Net® Systems Interface. This User Guide is designed to fami